Tesla coil

From Wikipedia, the free encyclopedia

Tesla coil

Tesla coil at Questacon - the National Science and Technology centre in Canberra, Australia.
Uses	Application in fluorescent lighting, electrotherapy, wireless power for electric power transmission, novelty lighting, as well as music.
Inventor	Nikola Tesla
Related items	Nikola Tesla, electrical transformer, electromagnetic field.

A Tesla coil is a type of resonant transformer circuit invented by Serbian-American scientist Nikola Tesla around 1891.^[1] It is usually used to generate very high voltage, low current, high frequency alternating current electricity. A Tesla coil consists of two, or sometimes three, coupled resonant electric circuits, but is difficult to define precisely, as Tesla experimented with a large variety of coils and configurations. Tesla used these coils to conduct innovative experiments in electrical lighting, fluorescence, x-rays, high frequency alternating current phenomena, electrotherapy, and wireless power for electric power transmission.

Early Tesla coil designs usually employed a high voltage power source, one or more high voltage capacitor(s), and a spark gap to excite the primary side of the Tesla coil system with periodic bursts of high frequency current. Later and higher-power coil designs had the primary and secondary circuits tuned so they resonated at the same (high) frequency (typically, between 25 kHz and 2 MHz). These larger Tesla coil designs are used to create long electrical discharges.

Tesla coil circuits were used commercially in sparkgap radio transmitters for wireless telegraphy until the 1920s^[1], and in electrotherapy and medical devices such as violet ray. Today their main use is entertainment and educational displays. Tesla coils are built by many high-voltage enthusiasts, research institutions, science museums and independent experimenters. Modified Tesla coils are widely used as igniters for high power gas discharge lamps, common examples being the mercury vapor and sodium types used for street lighting. Although electronic igniters are available, Tesla's original spark gap design is much cheaper and has proven extremely reliable.

[edit] History

[edit] Tesla's coil

The "American Electrician"^[2] gives a description of an early tesla coil wherein a glass battery jar, six inches by eight inches (15×20 cm), is wound with 60 to 80 turns of AWG No. 18 B & S magnet wire (0.823 mm²). Into this is slipped a primary consisting of eight to ten turns of AWG No. 6 B & S wire (13.3 mm²) and the whole combination immersed in a vessel containing linseed or mineral oil. (Norrie, pg. 34-35)

[edit] Disruptive "Tesla" coils

Early Disruptive Coils

Imitation of a Hertzian Spark Gap

A configuration of his coils; Tesla's Disruptive Discharge Coil Box.

In the spring of 1891, Tesla gave demonstrations with various machines before the American Institute of Electrical Engineers at Columbia College. Following the initial research of voltage and frequency by William Crookes, Tesla designed and constructed a series of coils that produced high-voltage, high-frequency currents. These early coils used a disruptive discharge across a spark gap in their operation. The setup can be duplicated by a Ruhmkorff coil, two capacitors (then called condensers), and a second, specially constructed, disruptive coil. (Norrie, pg. 228)

In U.S. Patent 0,454,622 , System of Electric Lighting (1891 June 23), Tesla described this early disruptive coil. It was devised for the purpose of converting and supplying electrical energy in a form suited for the production of certain novel electrical phenomena, which require currents of higher frequency and potential. It also specified an energy storage capacitor and discharger mechanism on the primary side of a radio-frequency transformer. This is the first-ever disclosure of a practical RF power supply capable of exciting an antenna to emit powerful electromagnetic radiation.

Another early Tesla coil was protected in 1897 by U.S. Patent 0,593,138 , "Electrical Transformer". This transformer developed currents of high potential and was composed of a primary and secondary coil (optionally, one terminal of the secondary could be electrically connected with the primary; similar to modern ignition coils). This Tesla coil had the secondary being inside of, and surrounded by, the convolutions of the primary coil. This Tesla coil consisted of a primary and secondary wound in the form of a flat spiral. One coil, the secondary in step-up transformation, of the device consisted of a longer fine-wire. The apparatus was also connected to ground when the coil was in use.

The Ruhmkorff coil, being fed from a main source, is wired to capacitors on both ends in series. A spark gap is placed in parallel to the Ruhmkorff coil before the capacitors. The discharge tips were usually metal balls under one inch (25 mm) in diameter, though Tesla used various forms of dischargers. The capacitors were of a special design, small with high insulation. These capacitors consisted of plates in oil that were movable. The smaller the plates, the more frequent the discharge of this early coil apparatus. The plates also help nullify the high self inductance of the secondary coil by adding capacitance to it. Mica plates were placed in the spark gap to establish an air current jet to go up through the gap. This helped to extinguish the arc, making the discharge more abrupt. An air blast was also used for this objective. (Norrie, pg. 230–231)

The capacitors are connected to a double primary (each coil in series with a capacitor). These are part of the second specially constructed disruptive coil. The primaries each have twenty turns of No. 16 (1.31 mm²) B & S rubber covered wire and are wound separately on rubber tubes not less than a 1/8th inch (3.2 mm) thick. The secondary has three hundred turns of No. 30 (0.0509 mm²) B & S silk-covered magnet wire, wound on rubber tube or rod, and the ends encased in glass or rubber tubes. The primaries must be large enough to be loose when the secondary coil is placed between the coils. The primaries must cover around two inches (50 mm) of the secondary. A hard rubber division must be placed between these primary coils. The ends of the primaries not connected with the capacitors are led to a spark gap. (Norrie, pg. 35–36)

[edit] Later Tesla coil design

Later Coil Design
U.S. Patent 1,119,732  View in elevation Free terminal and circuit of large surface with supporting structure and generating apparatus	Tesla coil transformer wound in the form of a flat spiral. This is the transmitter form as described in U.S. Patent 645,576 .

Tesla, in U.S. Patent 0,645,576  System of Transmission of Electrical Energy and U.S. Patent 0,649,621  Apparatus for Transmission of Electrical Energy, described new and useful combinations of transformer coils. The transmitting coil or conductor arranged and excited to cause currents or oscillation to propagate through conduction through the natural medium from one point to another remote point therefrom and a receiver coil or conductor of the transmitted signals.^[3] The production of currents of very high potential could be attained in these coils. He would later attain U.S. Patent 0,723,188 , Method of Signaling, and U.S. Patent 0,725,605 , System of Signaling, for coils with elevated transmitter capacitance with an Earth electrode.

Some of Tesla's later coils were considerably larger and operated at much higher power levels. When Tesla patented a later device in U.S. Patent 1,119,732  (Apparatus for Transmitting Electrical Energy), he called the device a high-voltage, air-core, self-regenerative resonant transformer that generates very high voltages at high frequency. However, this phrase is no longer in conventional use.

Tesla's later systems were usually powered from large high voltage power transformers, used banks of Leyden jar capacitors immersed in oil (to reduce corona losses), and used rotating spark gaps to handle the higher power levels. A rotating spark gap combines the ventilator needed to cool a fixed spark gap and the spark gap into a single device. The synchronous version uses a very simple electric motor, that is a permanent magnet encompassing a coil driven by the line voltage. But it needs to be started like the propeller of a biplane. It reduces spark gap losses, because it uses only two gaps, and it allows to extinguish the spark on zero passage.

Tesla also dispensed with using oil to insulate his transformer coils, relying instead on the insulating properties of air. Tesla coils achieve great gain in voltage by loosely coupling two resonant LC circuits, using an air-core (ironless) transformer. Although modern Tesla coils are usually designed to generate long sparks, Tesla's original systems were designed for wireless communication. Tesla used top terminals (toploads) having large radii of curvature to prevent losses from corona and sparks (often called streamers). The voltage gain of the circuit with a free, or an elevated, toroid is proportional to the quantity of charge displaced, which is determined by the product of the capacitance of the circuit, the voltage (which Tesla called "pressure" in the sense of a hydraulic analogy), and the frequency of the currents employed.

[edit] Tesla coil operation

A Tesla coil transformer operates in a significantly different fashion than a conventional (i.e., iron core) transformer. In a conventional transformer, the windings are very tightly coupled, and voltage gain is limited to the ratio of the numbers of turns in the windings. However, the voltage gain of a disruptive Tesla coil can be significantly greater, since it is instead proportional to the square root of the ratio of secondary and primary inductances. The coil transfers energy from one oscillating resonant circuit (the primary) to the other (the secondary) over a number of RF cycles. As the primary energy transfers to the secondary, the secondary's output voltage increases until all of the available primary energy has been transferred to the secondary (less losses). Even with significant spark gap losses, a well designed Tesla coil can transfer over 85% of the energy initially stored in the primary capacitor to the secondary circuit.

Electric discharge showing the lightning-like plasma filaments from a Tesla coil.

Modern high voltage enthusiasts usually build Tesla coils that are similar to some of Tesla's "later" air core designs. These typically consist of a primary tank circuit, which is a series LC (inductance-capacitance) circuit composed of a high voltage capacitor, spark gap, and primary coil; and the secondary LC circuit, a series resonant circuit consisting of the secondary coil and the toroid. In Tesla's original plans, the secondary LC circuit is composed of a loaded secondary coil which is then placed in series with a large helical coil. The helical coil was then connected to the toroid. Most modern coils use only a single secondary coil. The toroid actually forms one terminal of a capacitor, the other terminal being the Earth (or "ground"). The primary LC circuit is "tuned" so that it will resonate at the same frequency as the secondary LC circuit. The primary and secondary coils are magnetically coupled, creating a dual-tuned resonant air-core transformer. However, unlike a conventional transformer, which may couple 97%+ of the magnetic fields between windings, a Tesla coil's windings are "loosely" coupled, with the primary and secondary typically sharing only 10–20% of their respective magnetic fields. Earlier oil insulated Tesla coils needed large and long insulations at their connections to prevent discharge in air. Later version Tesla coils spread their electric fields over large distances to prevent high electrical stresses in the first place, thereby allowing operation in free air.

Tesla's original design for his largest coil used a top terminal consisting of a metallic frame in the shape of a toroid, covered with smooth half circular metal plates (constituting a very large conducting surface). On his largest system, Tesla employed on this type of shaped element within a dome. The top terminal has relatively small capacitance, charged to as high a voltage as practicable.^[4] The outer surface of the elevated conductor is where the electrical charge chiefly accumulates. It has a large radius of curvature, or is composed of separate elements which, irrespective of their own radii of curvature, are arranged close to each other so that the outside ideal surface enveloping them has a large radius.^[5] This design allowed the terminal to support very high voltages without generating corona or sparks. Tesla during his patent application process described a variety of resonator terminals at the top of this later coil.^[6] Most Modern Tesla coils use simple toroids, typically fabricated from spun metal or flexible aluminum ducting, to control the high electrical field near the top of the secondary and to direct spark outward, and away, from the primary and secondary windings.

Some of Tesla's work involved a more tightly coupled, air core, high frequency transformer, the output of which then fed another resonator, sometimes called an "extra coil", or simply an "upper secondary". The principle is that energy accumulates in the resonating, upper coil, and the role of transformer secondary is played by the separate, "lower" secondary; the roles are not shared by a single secondary. Modern three-coil Magnifying transmitter systems often either placed the upper secondary some distance from the transformer, or wound it on a considerably smaller diameter coil form. Direct magnetic coupling to the upper secondary was not desirable, since the third coil was designed to be driven directly by injecting RF current directly into the bottom end of the winding.

This particular Tesla circuit consists of a coil in close inductive relation with a primary, and one end of which is connected to a ground-plate, while its other end is led through a separate self-induction coil (whose connection should always be made at, or near, the geometrical center of that coil's circular aspect, in order to secure a symmetrical distribution of the current), and of a metallic cylinder carrying the current to the terminal. The primary coil may be excited by any desired source of high frequency current. The important requirement is that the primary and secondary sides must be tuned to the same resonant frequency to allow efficient transfer of energy between the primary and secondary resonant circuits. The conductor of the shaft to the terminal (topload) is in the form of a cylinder with smooth surface of a radius much larger than that of the spherical metal plates, and widens out at the bottom into a hood (which is slotted to avoid loss by eddy currents and for safety). The secondary coil is wound on a drum of insulating material, with its turns close together. When the effect of the small radius of curvature of the wire itself is overcome, the lower secondary coil behaves as a conductor of large radius of curvature, corresponding to that of the drum (this effect is applicable elsewhere). The lower end of the upper secondary coil, if desired, may be extended up to the terminal U.S. Patent 1,119,732  and should be somewhat below the uppermost turn of the primary coil. This lessens the tendency of the charge to break out from the wire connecting both and to pass along the support.

Demonstration of the Nevada Lightning Laboratory 1:12 scale prototype twin Tesla Coil at Maker Faire 2008.

Modern day transistor or vacuum tube Tesla coils do not use a spark gap. Instead, the transistor(s) or vacuum tube(s) provide the switching or amplifying function necessary to generate RF power for the primary circuit. Transistor Tesla coils use the lowest primary operating voltage, typically between 155 to 800 volts, and drive the primary winding using either a half-bridge or full-bridge arrangement of bipolar transistors, MOSFETs or IGBTs to switch the primary current. Vacuum tube coils typically operate with plate voltages between 1500 and 6000 volts, while most spark gap coils operate with primary voltages of 6,000 to 25,000 volts. The primary winding of a traditional transistor Tesla coil is wound around only the bottom portion of the secondary (sometimes called the resonator). This helps to illustrate operation of the secondary as a pumped resonator. The primary induces alternating voltage into the bottommost portion of the secondary, providing regular "pushes" (similar to provided properly timed pushes to a playground swing). Additional energy is transferred from the primary to the secondary inductance and topload capacitance during each "push", and secondary output voltage builds (called ring-up). An electronic feedback circuit is usually used to adaptively synchronize the primary oscillator to the growing resonance in the secondary, and this is the only tuning consideration beyond the initial choice of a reasonable topload.

In a Doubly Resonant Solid State Tesla Coil (DRSSTC), the electronic switching of the SSTC is combined with the resonant primary circuit of a spark-gap Tesla coil. The resonant primary circuit is formed by connecting a capacitor in series with the primary winding of the coil, so that the combination forms a series tank circuit with a resonant frequency near that of the secondary circuit. Because of the additional resonant circuit, one manual and one adaptive tuning adjustment are necessary. Also, an interrupter is usually used to reduce the duty cycle of the switching bridge, in order to improve peak power capabilities; similarly, IGBTs are more popular in this application than bipolar transistors or MOSFETs, due to their superior power handling characteristics. Performance of a DRSSTC can be comparable to a medium power spark gap Tesla coil, and efficiency (as measured by spark length versus input power) can be significantly greater than a spark gap Tesla coil operating at the same input power.

Although even the relatively low primary circuit voltage of transistor Tesla coils can be quite dangerous, all known fatalities (one hobbyist, one bystander, and one child)^{[citation needed]} have, thus far, been from spark gap driven coils.^{[citation needed]}

[edit] Utilization and production

Transmission

Typical Tesla Coil Schematic This example circuit is designed to be driven by alternating currents. Here the spark gap shorts the high frequency across the first transformer. An inductance, not shown, protects the transformer.

Alternate Tesla Coil Configuration This circuit also driven by alternating currents. However, here the AC supply transformer must be capable of withstanding high voltages at high frequencies.

[edit] Electrical transmission

A large Tesla coil of more modern design often operates at very high peak power levels, up to many megawatts (a million watts^[7]). It should therefore be adjusted and operated carefully, not only for efficiency and economy, but also for safety. If, due to improper tuning, the maximum voltage point occurs below the terminal, along the secondary coil, a discharge (spark) may break out and damage or destroy the coil wire, supports, or nearby objects.

Tesla experimented with these, and many other, circuit configurations (see right). The Tesla coil primary winding, spark gap and tank capacitor are connected in series. In each circuit, the AC supply transformer charges the tank capacitor until its voltage is sufficient to break down the spark gap. The gap suddenly fires, allowing the charged tank capacitor to discharge into the primary winding. Once the gap fires, the electrical behavior of either circuit is identical. Experiments have shown that neither circuit offers any marked performance advantage over the other.

However, in the typical circuit (above), the spark gap's short circuiting action prevents high frequency oscillations from 'backing up' into the supply transformer. In the alternate circuit, high amplitude high frequency oscillations that appear across the capacitor also are applied to the supply transformer's winding. This can induce corona discharges between turns that weaken and eventually destroy the transformer's insulation. Experienced Tesla coil builders almost exclusively use the top circuit, often augmenting it with low pass filters (resistor and capacitor (RC) networks) between the supply transformer and spark gap to help protect the supply transformer. This is especially important when using transformers with fragile high voltage windings, such as Neon-sign transformers (NSTs). Regardless of which configuration is used, the HV transformer must be of a type that self-limits its secondary current by means of internal leakage inductance. A normal (low leakage inductance) high voltage transformer must use an external limiter (sometimes called a ballast) to limit current. NSTs are designed to have high leakage inductance to limit their short circuit current to a safe level.

[edit] Tuning precautions

The primary coil's resonant frequency should be tuned to that of the secondary, using low-power oscillations, then increasing the power until the apparatus has been brought under control. While tuning, a small projection (called a "breakout bump") is often added to the top terminal in order to stimulate corona and spark discharges (sometimes called streamers) into the surrounding air. Tuning can then be adjusted so as to achieve the longest streamers at a given power level, corresponding to a frequency match between the primary and secondary coil. Capacitive 'loading' by the streamers tends to lower the resonant frequency of a Tesla coil operating under full power. For a variety of technical reasons, toroids provide one of the most effective shapes for the top terminals of Tesla coils.

[edit] Air discharges

A small, later-type "Tesla coil" in operation. The output is giving 17-inch sparks. The diameter of the secondary is three inches. The power source is a 10000 V, 60 Hz current limited supply.

While generating discharges, electrical energy from the secondary and toroid is transferred to the surrounding air as electrical charge, heat, light, and sound. The electric currents that flow through these discharges are actually due to the rapid shifting of quantities of charge from one place (the top terminal) to other places (nearby regions of air). The process is similar to charging or discharging a capacitor. The current that arises from shifting charges within a capacitor is called a displacement current. Tesla coil discharges are formed as a result of displacement currents as pulses of electrical charge are rapidly transferred between the high voltage toroid and nearby regions within the air (called space charge regions). Although the space charge regions around the toroid are invisible, they play a profound role in the appearance and location of Tesla coil discharges.

When the spark gap fires, the charged capacitor discharges into the primary winding, causing the primary circuit to oscillate. The oscillating primary current creates a magnetic field that couples to the secondary winding, transferring energy into the secondary side of the transformer and causing it to oscillate with the toroid capacitance. The energy transfer occurs over a number of cycles, and most of the energy that was originally in the primary side is transferred into the secondary side. The greater the magnetic coupling between windings, the shorter the time required to complete the energy transfer. As energy builds within the oscillating secondary circuit, the amplitude of the toroid's RF voltage rapidly increases, and the air surrounding the toroid begins to undergo dielectric breakdown, forming a corona discharge.

As the secondary coil's energy (and output voltage) continue to increase, larger pulses of displacement current further ionize and heat the air at the point of initial breakdown. This forms a very conductive "root" of hotter plasma, called a leader, that projects outward from the toroid. The plasma within the leader is considerably hotter than a corona discharge, and is considerably more conductive. In fact, it has properties that are similar to an electric arc. The leader tapers and branches into thousands of thinner, cooler, hairlike discharges (called streamers). The streamers look like a bluish 'haze' at the ends of the more luminous leaders, and it is the streamers that actually transfer charge between the leaders and toroid to nearby space charge regions. The displacement currents from countless streamers all feed into the leader, helping to keep it hot and electrically conductive.

In a spark gap Tesla coil the primary-to-secondary energy transfer process happens repetitively at typical pulsing rates of 50–500 times/second, and previously formed leader channels don't get a chance to fully cool down between pulses. So, on successive pulses, newer discharges can build upon the hot pathways left by their predecessors. This causes incremental growth of the leader from one pulse to the next, lengthening the entire discharge on each successive pulse. Repetitive pulsing causes the discharges to grow until the average energy that's available from the Tesla coil during each pulse balances the average energy being lost in the discharges (mostly as heat). At this point, dynamic equilibrium is reached, and the discharges have reached their maximum length for the Tesla coil's output power level. The unique combination of a rising high voltage Radio Frequency envelope and repetitive pulsing seem to be ideally suited to creating long, branching discharges that are considerably longer than would be otherwise expected by output voltage considerations alone. High voltage discharges create filamentary multi-branched discharges which are purplish blue in colour. High energy discharges create thicker discharges with fewer branches, are pale and luminous, almost white, and are much longer than low energy discharges, because of increased ionisation. There will be a strong smell of ozone and nitrogen oxides in the area. The important factors for maximum discharge length appear to be voltage, energy, and still air of low to moderate humidity. However, even more than 100 years later after the first use of Tesla coils, there are many aspects of Tesla coil discharges and the energy transfer process that are still not completely understood.

[edit] Electrical reception

Variants of Tesla coils were suggested by Tesla for receiving power from electromagnetic radiation of practicable frequency, and were suggested for exploiting the vertical voltage gradient in the Earth's atmosphere. Tesla built and used various devices for detecting radio frequency energy. He felt that several of his experiments were operating on a basis of Hertzian waves, electromagnetic waves propagated in space without artificial guide.^[8] During his work at Colorado Springs, Tesla believed that he had established an electrical resonance in the entire Earth using the Tesla coil transmitter at his laboratory operating at about 150,000 hertz (cycles per second) and about 300 horsepower (224,000 watts).^[9] He used one of his resonators (secondaries) with a tap near the bottom for his reception work.

Tesla stated that one of the seven features of this world wireless system was the construction of a "resonant receiver".^[10] The secondary of a Tesla coil and its capacitor can be used in receive mode.^{[11][12][13][14][15][16]} Tesla himself demonstrated wireless transmission of electric power from his transmitter to his receiver. These concepts and methods are part of his wireless transmission of electric power distribution system (US1119732 — Apparatus for Transmitting Electrical Energy — 1902 January 18). Tesla made a proposal that there needed to be "thirty" such antennas worldwide.^[17] The receiving circuit of these towers are connected each with a condenser and a device adapted to open and close the receiving circuit at predetermined intervals of time.^[18] The Tesla coil receiver has means for commutating, directing, or selecting the current impulses in the charging circuit so as to render them suitable for charging the storage device, a device for closing the receiving-circuit, and means for causing the receiver to be operated by the energy accumulated.^[19]

Tesla coil in one experiment of many conducted in Colorado Springs. This is a grounded tuned coil in resonance with a distant transmitter; Light is glowing near the bottom.

A Tesla coil used as an electrical power receiver is referred to as a Tesla Antenna.^{[20][21][22][23]} The Tesla antenna as a receiver acts as a step-down transformer with high current output.^[24] The parameters of a Tesla coil transmitter are identically applicable to it being a receiver (e.g., an antenna circuit), due to reciprocity. Impedance, generally though, is not applied in an obvious way; for electrical impedance, the impedance at the load (e.g., where the power is consumed) is most critical and, for a Tesla coil receiver, this is at the point of utilization (such as at an induction motor) rather than at the receiving node. Complex impedance of an antenna is related to the electrical length of the antenna at the wavelength in use. Commonly, impedance is adjusted at the load with a tuner or a matching networks composed of inductors and capacitors.

A Tesla coil can receive electromagnetic impulses^[25] from atmospheric electricity^[26][27][28] and radiant energy,^[29][30] besides normal wireless transmissions. Radiant energy throws off with great velocity minute particles which are strongly electrified and other rays falling on the insulated-conductor connected to a condenser (i.e., a capacitor) can cause the condenser to indefinitely charge electrically.^[31] The helical resonator can be "shock excited" due to radiant energy disturbances not only at the fundamental wave at one-quarter wave-length but also is excited at its harmonics. Hertzian methods can be used to excite the Tesla Antenna with limitations that result in great disadvantages for utilization, though.^[32] The methods of ground conduction and the various induction methods can also be used to excite the Tesla Antenna, but are again at a disadvantages for utilization.^[33] The charging-circuit can be adapted to be energized by the action of various other disturbances and effects at a distance. Arbitrary and intermittent oscillations that are propagated via conduction to the receiving resonator will charge the receiver's capacitor and utilize the potential energy to greater effect.^[34] Various radiations can be used to charge and discharge conductors, with the radiations considered electromagnetic vibrations of various wavelengths and ionizing potential.^[35] The Tesla Antenna utilizes the effects or disturbances to charge a storage device with energy from an external source (natural or man-made) and controls the charging of said device by the actions of the effects or disturbances (during succeeding intervals of time determined by means of such effects and disturbances corresponding in succession and duration of the effects and disturbances).^[36] The stored energy can also be used to operate the receiving device. The accumulated energy can, for example, operate a transformer by discharging through a primary circuit at predetermined times which, from the secondary currents, operate the receiving device.^[37]

While Tesla coils can be used for these purposes, much of the public and media attention is toward the transmitting applications of the Tesla coil since the plasma discharges are fascinating to most people. Regardless of this fact, Tesla did suggest that this variation of the Tesla coil could utilize the phantom loop effect to form a circuit to induct energy from the Earth's magnetic field and other radiant energy sources (including, but not limited to, electrostatics^[38]). With regard to Tesla's statements on the harnessing of natural phenomena to obtain electric power, he stated:

Ere many generations pass, our machinery will be driven by a power obtainable at any point of the universe. — "Experiments with Alternate Currents of High Potential and High Frequency" (February 1892)

Tesla stated that the output power from these devices, attained from Hertzian methods of charging, was low,^[39] but alternative charging means are available. Tesla receivers operated correctly, act as a step-down transformer with high current output.^[40] There are, to date, no commercial power generation entities or businesses that have utilized this technology to full effect. The power levels achieved by Tesla coil receivers have, thus far, been a fraction of the output power of the transmitters.^{[citation needed]}

Ignoring earth currents and other natural electromagnetic phenomena the Tesla antenna can receive, atmospheric electricity's total power of only all the sky-to-ground lightning everywhere on Earth from moment to moment has been stated at 700 megawatts.^[41] By comparison, a typical fossil fuel power plant (such as oil or gas) feeding the utility grid may have two gas turbines and a single steam turbine utilizing the heat from the discharged flue gas of the gas turbines, with each of the three turbines rated at 100 megawatts. On the load side, 700 MW is seen to correspond to two million parsimonious households averaging 350 watts of power use, contrasted with a world population of over six billion people. As regards methods, atmospheric electricity includes static electricity and other phenomena. Modern HVDC technology inverts DC at such voltages to AC well enough to be very popular for use in the power grid; a Tesla coil variant is not the only way to do this, nor necessarily the best way, either for atmospheric electricity or telluric power.^[42] Earth's surface has a negative charge and the atmosphere has a positive charge.

The amount of electromagnetic radiation present on the surface of the Earth is known to those whose technical work on radio communication or regulatory compliance involves reception and measurement. Radiation is monitored from ten-thousands of hertz (cycles per second) up to thirty billion hertz (wavelength one centimeter) or more, in many cases. Authorized radio transmissions and minor but unwanted emissions from equipment being designed are not greatly overshadowed by naturally occurring radio frequency energy.^[43] This natural and unnatural 'noise' is abundant in the environment and can be received via wideband reception, although this article does not cite any demonstration providing power on the scale needed for household, commercial or industrial purposes at the present time. A Tesla coil is not a wideband device insofar as it operates only on its resonant frequency and certain harmonics.

[edit] The 'skin effect' and high frequency electrical safety

Student conducting Tesla coil streamers through his body, 1909

The dangers of contact with high frequency electrical current are sometimes perceived as being less than at lower frequencies, because the subject usually doesn't feel pain or a 'shock'. This is often erroneously attributed to skin effect, a phenomenon that tends to inhibit alternating current from flowing inside conducting media. It was thought that in the body, Tesla currents travelled close to the skin surface, making them safer than lower frequency electric currents. In fact, in the early 1900s a major use of Tesla coils was to apply high frequency current directly to the body in electrotherapy.

Although skin effect limits Tesla currents to the outer fraction of an inch in metal conductors, the 'skin depth' of human flesh at typical Tesla coil frequencies is still of the order of 60 inches (152 cm) or more.^{[44][45][46][47][48]} This means that high frequency currents will still preferentially flow through deeper, better conducting, portions of an experimenter's body such as the circulatory and nervous systems. The reason for the lack of pain is that a human being's nervous system does not sense the flow of potentially dangerous electrical currents above 15–20 kHz; essentially, in order for nerves to be activated, a significant number of ions must cross their membrane before the current (and hence voltage) reverses. Since the body no longer provides a warning 'shock', novices may touch the output streamers of small Tesla coils without feeling painful shocks. However, there is anecdotal evidence among Tesla coil experimenters that temporary tissue damage may still occur and be observed as muscle pain, joint pain, or tingling for hours or even days afterwards. This is believed to be caused by the damaging effects of internal current flow, and is especially common with continuous wave (CW), solid state or vacuum tube type Tesla coils. It is, however, of note that certain transformers can be used to provide alternating current with a frequency high enough so that the skin depth becomes small enough for the voltage to be safe. As this number is inversely proportional to the root of the frequency, this is fairly high; the number is in the megahertz.

Large Tesla coils and magnifiers can deliver dangerous levels of high frequency current, and they can also develop significantly higher voltages (often 250,000–500,000 volts, or more). Because of the higher voltages, large systems can deliver higher energy, potentially lethal, repetitive high voltage capacitor discharges from their top terminals. Doubling the output voltage quadruples the electrostatic energy stored in a given top terminal capacitance. If an unwary experimenter accidentally places himself in path of the high voltage capacitor discharge to ground, the low current electric shock can cause involuntary spasms of major muscle groups and may induce life-threatening ventricular fibrillation and cardiac arrest. Even lower power vacuum tube or solid state Tesla coils can deliver RF currents that are capable of causing temporary internal tissue, nerve, or joint damage through Joule heating. In addition, an RF arc can carbonize flesh, causing a painful and dangerous bone-deep RF burn that may take months to heal. Because of these risks, knowledgeable experimenters avoid contact with streamers from all but the smallest systems. Professionals usually use other means of protection such as a Faraday cage or a chain mail suit to prevent dangerous currents from entering their body.

The most serious dangers associated with Tesla coil operation are associated with the primary circuit. It is the primary circuit that is capable of delivering a sufficient current at a significant voltage to stop the heart of a careless experimenter. Because these components are not the source of the trademark visual or auditory coil effects, they may easily be overlooked as the chief source of hazard. Should a high frequency arc strike the exposed primary coil while, at the same time, another arc has also been allowed to strike to a person, the ionized gas of the two arcs form a circuit that may conduct lethal, low-frequency current from the primary into the person. This is believed to have been the cause of death of a professional Tesla coil demonstrator, Henry Leroy Transtrom, in 1951.

Further, great care should be taken when working on the primary section of a coil even when it has been disconnected from its power source for some time. The tank capacitors can remain charged for days with enough energy to deliver a fatal shock. Proper designs should always include 'bleeder resistors' to bleed off stored charge from the capacitors. In addition, a safety shorting operation should be performed on each capacitor before any internal work is performed.^[49]

[edit] Instances and devices

Magnifier Configurations
Classically driven configuration.[50]	Later-type driven configuration. Pancake may be horizontal; lead to resonator is kept clear of it.[51]

Tesla's Colorado Springs laboratory possessed one of the largest Tesla coils ever built, known as the "Magnifying Transmitter". The Magnifying Transmitter is somewhat different from classic 2-coil Tesla coils. A Magnifier uses a 2-coil 'driver' to excite the base of a third coil ('resonator') that is located some distance from the driver. The operating principles of both systems are similar. The world's largest currently existing 2-coil Tesla coil is a 130,000 watt unit, part of a 38 foot tall sculpture. It is owned by Alan Gibbs and currently resides in a private sculpture park at Kakanui Point near Auckland, New Zealand.^[52]

The Tesla coil is an early predecessor (along with the induction coil) of a more modern device called a flyback transformer, which provides the voltage needed to power the cathode ray tube used in some televisions and computer monitors. The disruptive discharge coil remains in common use as the ignition coil^[53][54] or spark coil in the ignition system of an internal combustion engine. These two devices do not use resonance to accumulate energy, however, which is the distinguishing feature of a Tesla coil. They do use inductive "kick", the forced, abrupt decay of the magnetic field, such that a voltage is provided by the coil at its primary terminals that is much greater than the voltage that was applied to establish the magnetic field, and it is this higher voltage that is then multiplied by the transformer turns ratio. Thus, they do store energy, and a Tesla resonator stores energy. A modern, low power variant of the Tesla coil is also used to power plasma globe sculptures and similar devices.

Scientists working with a glass vacuum line (e.g. chemists working with volatile substances in the gas phase, inside a system of glass tubes, taps and bulbs) test for the presence of tiny pin-holes in the apparatus (especially a newly blown piece of glassware) using a Tesla coil. When the system is evacuated and the discharging end of the coil moved over the glass, the discharge travels through any pin-hole immediately below it and thus illuminates the hole, indicating points that need to be annealed or re-blown before they can be used in an experiment.

[edit] Popularity

Tesla coils are very popular devices among certain electrical engineers and electronics enthusiasts. Builders of Tesla coils as a hobby are called "coilers". The world's largest conical Tesla coil is on display at the Mid America Science Museum in Hot Springs, Arkansas. This coil produces 1.5 million volts of electrical potential. A very large tesla coil, designed and built by Syd Klinge, is shown every year at the Coachella music and arts festival, in Coachella, Indio, California, USA. There are "coiling" conventions where people attend with their home-made Tesla coils and other electrical devices of interest. It should be noted that there are rather significant safety issues^[49] regarding coil assembly and operation by hobbyists (including professional engineers), which may be discovered by study of the literature far more reliably than by only attempting one's own analysis.

Low power Tesla coils are also sometimes used as a high voltage source for Kirlian photography.^[55]

Tesla coils can also be used to create music by modulating the system's effective "break rate" (i.e., the rate and duration of high power RF bursts) via midi data and a control unit. The actual midi data is interpreted by a micro controller which converts the midi data into a PWM output which can be sent to the tesla coil via a fiber optic interface.^{[56] [57]} The YouTube video Super Mario Brothers theme in stereo and harmony on two coils shows a performance on matching solid state coils operating at 41 kHz. The coils were built and operated by designer hobbyists Jeff Larson and Steve Ward. The device has been named the Zeusaphone, after Zeus, Greek god of lightning, and as a play on words referencing the Sousaphone.

[edit] In fiction

Tesla coils are popular devices appearing in fiction. Several examples include:

• Tesla coils appear as weapons in many computer games, typically firing bolts of electricity at enemies. Other directed-energy weapons with the word "Tesla" in their name also appear. Examples of games featuring Tesla coils and other Tesla weapons are Command & Conquer: Red Alert, Tomb Raider: Legend, Blazing Angels 2: Secret Missions of WWII, Arcanum: Of Steamworks and Magick Obscura, Return to Castle Wolfenstein, Ratchet & Clank and World of Warcraft. Also in the Fallout series of games fictional Tesla Armour can be found. Tesla armor provides great protection from energy weapons because, in the game's context, the armor absorbs and dissipates most of the attack much like a Tesla coil does when discharging.
• The Jim Jarmusch film Coffee and Cigarettes (2003) featured a segment starring Jack and Meg White from the band The White Stripes entitled "Jack shows Meg his Tesla coil". In the segment, the pair are having a coffee. Jack explains the work of Nikola Tesla to Meg and demonstrates the coil he has by his side.
• In the novel by Christopher Priest and the film, The Prestige, one of the main characters, Robert Angier, seeks the help of Nikola Tesla (played by David Bowie in the film version) to construct a device to transport matter for the purposes of a stage 'magic act'. Tesla then creates a supposed variant of his Tesla coil to achieve this.
• A Tesla coil was used to produce all of the V'Ger lightning effects for "Star Trek: The Motion Picture" (1979). Production was carried out at an airfield by teams of crew members working around the clock in order to make the very-cramped schedule; so much so that other members of the production crew (including Special Visual Effects director/supervisor Douglas Trumbull) were called in to staff it.

[edit] Related patents

Tesla's patents

See also: List of Tesla patents

• "Electrical Transformer Or Induction Device". U.S. Patent No. 433,702, August 5, 1890^[58]
• "Means for Generating Electric Currents", U.S. Patent No. 514,168, February 6, 1894
• "Electrical Transformer", Patent No. 593,138, November 2, 1897
• "Method Of Utilizing Radiant Energy", Patent No. 685,958 November 5, 1901
• "Method of Signaling", U.S. Patent No. 723,188, March 17, 1903
• "System of Signaling", U.S. Patent No. 725,605, April 14, 1903
• "Apparatus for Transmitting Electrical Energy", January 18, 1902, U.S. Patent 1,119,732, December 1, 1914 (available at U.S. Patent 1,119,732  and tfcbooks' Apparatus for Transmitting Electrical Energy)

Others' patents

• J. S. Stone, U.S. Patent 714,832 , "Apparatus for amplifying electromagnetic signal-waves". (Filed January 23, 1901; Issued December 2, 1902)
• A. Nickle, U.S. Patent 2,125,804 , "Antenna". (Filed May 25, 1934; Issued August 2, 1938)
• William W. Brown, U.S. Patent 2,059,186 , "Antenna structure". (Filed May 25, 1934; Issued October 27, 1936).
• Robert B. Dome, U.S. Patent 2,101,674 , "Antenna". (Filed May 25, 1934; Issued December 7, 1937)
• Armstrong, E. H., U.S. Patent 1,113,149 , "Wireless receiving system". 1914.
• Armstrong, E. H., U.S. Patent 1,342,885 , "Method of receiving high frequency oscillation". 1922.
• Armstrong, E. H., U.S. Patent 1,424,065 , "Signalling system". 1922.
• Gerhard Freiherr Du Prel, U.S. Patent 1,675,882 , "High frequency circuit". (Filed August 11, 1925; Issued July 3, 1928)
• Leydorf, G. F., U.S. Patent 3,278,937 , "Antenna near field coupling system". 1966.
• Van Voorhies, U.S. Patent 6,218,998 , "Toroidal helical antenna"
• Gene Koonce, U.S. Patent 6,933,819 , "Multifrequency electro-magnetic field generator". (Filed October 29, 2004; Issued August 23, 2005)^[59]

[edit] See also

• 833A
• Bifilar coil
• List of Tesla patents
• Tesla turbine

[edit] Notes

[edit] Further reading

Wikimedia Commons has media related to: Tesla coil

Operation and other information

• Armagnat, H., & Kenyon, O. A. (1908). The theory, design and construction of induction coils. New York: McGraw.
• Haller, G. F., & Cunningham, E. T. (1910). The Tesla high frequency coil, its construction and uses. New York: D. Van Nostrand Co.
• Iannini, R. E. (2003). Electronic gadgets for the evil genius: 21 build-it-yourself projects. TAB electronics. New York: McGraw-Hill. Pages 137 – 202.
• Corum, Kenneth L. and James F. "Tesla Coils and the Failure of Lumped-Element Circuit Theory"
• Nicholson, Paul, "Tesla Secondary Simulation Project" (Current state of the art in rigorously describing Tesla coil secondary behavior through theoretical analysis, simulation and testing of results in practice)
• Beaty, Bill, "Nikola Tesla Coil Information".
• Vujovic, Ljubo, "Tesla Coil". Tesla Memorial Society of New York.
• Hickman, Bert, "Tesla Coil Information Center"
• Cooper, John. F., "Magnifying Transmitter early-type circuit diagram; Later-type circuit diagram". Tesla-Coil.com

Electrical World

• "The Development of High Frequency Currents for Practical Application"., The Electrical World, Vol 32, No. 8.
• "Boundless Space: A Bus Bar". The Electrical World, Vol 32, No. 19.

Other publications

• A. L. Cullen, J. Dobson, "The Corona Breakdown of Aerials in Air at Low Pressures". Proceedings of the Royal Society of London. Series A, Mathematical and Physical Sciences, Vol. 271, No. 1347 (February 12, 1963), pp. 551–564
• Bieniosek, F. M., "Triple Resonance Pulse Transformer Circuit". Review of Scientific Instruments, 61 (6).
• Corum, J. F., and K. L. Corum, "RF Coils, Helical Resonators and Voltage Magnification by Coherent Spatial Modes". IEEE, 2001.
• de Queiroz, Antonio Carlos M., "Synthesis of Multiple Resonance Networks". Universidade Federal do Rio de Janeiro, Brazil. EE/COPE.
• Haller, George Francis, and Elmer Tiling Cunningham, "The Tesla high frequency coil, its construction and uses". New York, D. Van Nostrand company, 1910.
• Hartley, R. V. L., "Oscillations with Non-linear Reactances". Bell Systems Technical Journal, Sun Publishing. 1992.
• Norrie, H. S., "Induction Coils: How to make, use, and repair them". Norman H. Schneider, 1907, New York. 4th edition.
• Reed, J. L., "Greater voltage gain for Tesla transformer accelerators", Review of Scientific Instruments, 59, p.2300, (1988).
• Curtis, Thomas Stanley, High Frequency Apparatus: Its Construction and Practical Application. Everyday Mechanics Co., 1916.
• A Huge Tesla Coil. By Father Francois Magri - Scientific American Aug. 8, 1914

[edit] External links

• Tesla coil at the Open Directory Project