Control chart
From Wikipedia, the free encyclopedia
The control chart, also known as the Shewhart chart or processbehaviour chart, in statistical process control is a tool used to determine whether a manufacturing or business process is in a state of statistical control or not.
Contents 
[edit] Overview
If the chart indicates that the process is currently under control then it can be used with confidence to predict the future performance of the process. If the chart indicates that the process being monitored is not in control, the pattern it reveals can help determine the source of variation to be eliminated to bring the process back into control. A control chart is a specific kind of run chart that allows significant change to be differentiated from the natural variability of the process.
This is key to effective process control and improvement. On a practical level the control chart can be seen as part of an objective disciplined approach that facilitates the decision as to whether process performance warrants attention or not.
The control chart is one of the seven basic tools of quality control (along with the histogram, Pareto chart, check sheet, causeandeffect diagram, flowchart, and scatter diagram).
[edit] History
The control chart was invented by Walter A. Shewhart while working for Bell Labs in the 1920s. The company's engineers had been seeking to improve the reliability of their telephony transmission systems. Because amplifiers and other equipment had to be buried underground, there was a business need to reduce the frequency of failures and repairs. By 1920 they had already realized the importance of reducing variation in a manufacturing process. Moreover, they had realized that continual processadjustment in reaction to nonconformance actually increased variation and degraded quality. Shewhart framed the problem in terms of Common and specialcauses of variation and, on May 16, 1924, wrote an internal memo introducing the control chart as a tool for distinguishing between the two. Dr. Shewhart's boss, George Edwards, recalled: "Dr. Shewhart prepared a little memorandum only about a page in length. About a third of that page was given over to a simple diagram which we would all recognize today as a schematic control chart. That diagram, and the short text which preceded and followed it, set forth all of the essential principles and considerations which are involved in what we know today as process quality control." ^{[1]} Shewhart stressed that bringing a production process into a state of statistical control, where there is only commoncause variation, and keeping it in control, is necessary to predict future output and to manage a process economically.
Dr. Shewhart created the basis for the control chart and the concept of a state of statistical control by carefully designed experiments. While Dr. Shewhart drew from pure mathematical statistical theories, he understood data from physical processes never produce a "normal distribution curve" (a Gaussian distribution, also commonly referred to as a "bell curve"). He discovered that observed variation in manufacturing data did not always behave the same way as data in nature (Brownian motion of particles). Dr. Shewhart concluded that while every process displays variation, some processes display controlled variation that is natural to the process, while others display uncontrolled variation that is not present in the process causal system at all times.^{[2]}
In 1924 or 1925, Shewhart's innovation came to the attention of W. Edwards Deming, then working at the Hawthorne facility. Deming later worked at the United States Department of Agriculture and then became the mathematical advisor to the United States Census Bureau. Over the next half a century, Deming became the foremost champion and proponent of Shewhart's work. After the defeat of Japan at the close of World War II, Deming served as statistical consultant to the Supreme Commander of the Allied Powers. His ensuing involvement in Japanese life, and long career as an industrial consultant there, spread Shewhart's thinking, and the use of the control chart, widely in Japanese manufacturing industry throughout the 1950s and 1960s.
More recent use and development of control charts in the ShewhartDeming tradition has been championed by Donald J. Wheeler.
[edit] Chart Details
A control chart consists of the following:
 Points representing measurements of a quality characteristic in samples taken from the process at different times [the data]
 A centre line, drawn at the process characteristic mean which is calculated from the data
 Upper and lower control limits (sometimes called "natural process limits") that indicate the threshold at which the process output is considered statistically 'unlikely'
The chart may contain other optional features, including:
 Upper and lower warning limits, drawn as separate lines, typically two standard deviations above and below the centre line
 Division into zones, with the addition of rules governing frequencies of observations in each zone
 Annotation with events of interest, as determined by the Quality Engineer in charge of the process's quality
However in the early stages of use the inclusion of these items may confuse inexperienced chart interpreters.
[edit] Chart usage
If the process is in control, all points will plot within the control limits. Any observations outside the limits, or systematic patterns within, suggest the introduction of a new (and likely unanticipated) source of variation, known as a specialcause variation. Since increased variation means increased quality costs, a control chart "signaling" the presence of a specialcause requires immediate investigation.
This makes the control limits very important decision aids. The control limits tell you about process behaviour and have no intrinsic relationship to any specification targets or engineering tolerance. In practice, the process mean (and hence the centre line) may not coincide with the specified value (or target) of the quality characteristic because the process' design simply can't deliver the process characteristic at the desired level.
Control charts omit specification limits or targets because of the tendency of those involved with the process (e.g., machine operators) to focus on performing to specification when in fact the leastcost course of action is to keep process variation as low as possible. Attempting to make a process whose natural centre is not the same as the target perform to target specification increases process variability and increases costs significantly and is the cause of much inefficiency in operations. Process capability studies do examine the relationship between the natural process limits (the control limits) and specifications, however.
The purpose of control charts is to allow simple detection of events that are indicative of actual process change. This simple decision can be difficult where the process characteristic is continuously varying; the control chart provides statistically objective criteria of change. When change is detected and considered good its cause should be identified and possibly become the new way of working, where the change is bad then its cause should be identified and eliminated.
The purpose in adding warning limits or subdividing the control chart into zones is to provide early notification if something is amiss. Instead of immediately launching a process improvement effort to determine whether special causes are present, the Quality Engineer may temporarily increase the rate at which samples are taken from the process output until it's clear that the process is truly in control. Note that with three sigma limits, one expects to be signaled approximately once out of every 370 points on average, just due to commoncauses.
[edit] Choice of limits
Shewhart set 3sigma limits on the following basis.
 The coarse result of Chebyshev's inequality that, for any probability distribution, the probability of an outcome greater than k standard deviations from the mean is at most 1/k^{2}.
 The finer result of the VysochanskiiPetunin inequality, that for any unimodal probability distribution, the probability of an outcome greater than k standard deviations from the mean is at most 4/(9k^{2}).
 The empirical investigation of sundry probability distributions reveals that at least 99% of observations occurred within three standard deviations of the mean.
Shewhart summarised the conclusions by saying:
... the fact that the criterion which we happen to use has a fine ancestry in highbrow statistical theorems does not justify its use. Such justification must come from empirical evidence that it works. As the practical engineer might say, the proof of the pudding is in the eating.
Though he initially experimented with limits based on probability distributions, Shewhart ultimately wrote:
Some of the earliest attempts to characterise a state of statistical control were inspired by the belief that there existed a special form of frequency function f and it was early argued that the normal law characterised such a state. When the normal law was found to be inadequate, then generalised functional forms were tried. Today, however, all hopes of finding a unique functional form f are blasted.
The control chart is intended as a heuristic. Deming insisted that it is not a hypothesis test and is not motivated by the NeymanPearson lemma. He contended that the disjoint nature of population and sampling frame in most industrial situations compromised the use of conventional statistical techniques. Deming's intention was to seek insights into the cause system of a process ...under a wide range of unknowable circumstances, future and past .... He claimed that, under such conditions, 3sigma limits provided ... a rational and economic guide to minimum economic loss... from the two errors:
 Ascribe a variation or a mistake to a special cause when in fact the cause belongs to the system (common cause). (Also known as a Type I error)
 Ascribe a variation or a mistake to the system (common causes) when in fact the cause was special. (Also known as a Type II error)
[edit] Calculation of standard deviation
As for the calculation of control limits, the standard deviation required is that of the commoncause variation in the process. Hence, the usual estimator, in terms of sample variance, is not used as this estimates the total squarederror loss from both common and specialcauses of variation.
An alternative method is to use the relationship between the range of a sample and its standard deviation derived by Leonard H. C. Tippett, an estimator which tends to be less influenced by the extreme observations which typify specialcauses.
[edit] Rules for detecting signals
The most common sets are:
 The Western Electric rules
 The Wheeler rules (equivalent to the Western Electric zone tests^{[3]})
 The Nelson rules
There has been particular controversy as to how long a run of observations, all on the same side of the centre line, should count as a signal, with 7, 8 and 9 all being advocated by various writers.
The most important principle for choosing a set of rules is that the choice be made before the data is inspected. Choosing rules once the data have been seen tends to increase the Type I error rate owing to testing effects suggested by the data.
[edit] Alternative bases
In 1935, the British Standards Institution, under the influence of Egon Pearson and against Shewhart's spirit, adopted control charts, replacing 3sigma limits with limits based on percentiles of the normal distribution. This move continues to be represented by John Oakland and others but has been widely deprecated by writers in the ShewhartDeming tradition.
[edit] Performance of control charts
When a point falls outside of the limits established for a given control chart, those responsible for the underlying process are expected to determine whether a special cause has occurred. If one has, then that cause should be eliminated if possible. It is known that even when a process is in control (that is, no special causes are present in the system), there is approximately a 0.27% probability of a point exceeding 3sigma control limits. Since the control limits are evaluated each time a point is added to the chart, it readily follows that every control chart will eventually signal the possible presence of a special cause, even though one may not have actually occurred. For a Shewhart control chart using 3sigma limits, this false alarm occurs on average once every 1/0.0027 or 370.4 observations. Therefore, the incontrol average run length (or incontrol ARL) of a Shewhart chart is 370.4.
Meanwhile, if a special cause does occur, it may not be of sufficient magnitude for the chart to produce an immediate alarm condition. If a special cause occurs, one can describe that cause by measuring the change in the mean and/or variance of the process in question. When those changes are quantified, it is possible to determine the outofcontrol ARL for the chart.
It turns out that Shewhart charts are quite good at detecting large changes in the process mean or variance, as their outofcontrol ARLs are fairly short in these cases. However, for smaller changes (such as a 1 or 2sigma change in the mean), the Shewhart chart does not detect these changes efficiently. Other types of control charts have been developed, such as the EWMA chart and the CUSUM chart, which detect smaller changes more efficiently by making use of information from observations collected prior to the most recent data point.
[edit] Criticisms
Several authors have criticised the control chart on the grounds that it violates the likelihood principle. However, the principle is itself controversial and supporters of control charts further argue that, in general, it is impossible to specify a likelihood function for a process not in statistical control, especially where knowledge about the cause system of the process is weak.
Some authors have criticised the use of average run lengths (ARLs) for comparing control chart performance, because that average usually follows a geometric distribution, which has high variability and difficulties
[edit] Types of charts
Chart  Process observation  Process observations relationships  Process observations type  Size of shift to detect 

XbarR chart  Quality characteristic measurement within one subgroup  Independent  Variables  Large (≥ 1.5σ) 
XbarS chart  Quality characteristic measurement within one subgroup  Independent  Variables  Large (≥ 1.5σ) 
Shewhart individuals control chart (ImR chart or XmR chart)  Quality characteristic measurement for one observation  Independent  Variables  Large (≥ 1.5σ) 
Threeway chart  Quality characteristic measurement within one subgroup  Independent  Variables  Large (≥ 1.5σ) 
pchart  Fraction nonconforming within one subgroup  Independent  Attributes  Large (≥ 1.5σ) 
npchart  Number nonconforming within one subgroup  Independent  Attributes  Large (≥ 1.5σ) 
cchart  Number of nonconformances within one subgroup  Independent  Attributes  Large (≥ 1.5σ) 
uchart  Nonconformances per unit within one subgroup  Independent  Attributes  Large (≥ 1.5σ) 
EWMA chart  Exponentially weighted moving average of quality characteristic measurement within one subgroup  Independent  Attributes or variables  Small (< 1.5σ) 
CUSUM chart  Cumulative sum of quality characteristic measurement within one subgroup  Independent  Attributes or variables  Small (< 1.5σ) 
Time series model  Quality characteristic measurement within one subgroup  Autocorrelated  Attributes or variables  N/A 
Regression Control Chart  Quality characteristic measurement within one subgroup  Dependent of process control variables  Variables  Large (≥ 1.5σ) 
[edit] See also
 Common cause and special cause
 Analytic and enumerative statistical studies
 W. Edwards Deming
 Statistical process control
 Total Quality Management
 Six Sigma
 Process capability
[edit] Notes
 ^ Western Electric  A Brief History
 ^ "Why SPC?" British Deming Association SPC Press, Inc. 1992
 ^ Wheeler, Donald J.; Chambers, David S. (1992), Understanding statistical process control (2 ed.), Knoxville, Tennessee: SPC Press, p. 96, ISBN 9780945320135, OCLC 27187772
[edit] Bibliography
 Deming, W E (1975) "On probability as a basis for action." The American Statistician. 29(4), pp146152
 Deming, W E (1982) Out of the Crisis: Quality, Productivity and Competitive Position ISBN 0521305535.
 Oakland, J (2002) Statistical Process Control ISBN 0750657669.
 Shewhart, W A (1931) Economic Control of Quality of Manufactured Product ISBN 0873890760.
 Shewhart, W A (1939) Statistical Method from the Viewpoint of Quality Control ISBN 0486652327.
 Wheeler, D J (2000) Normality and the ProcessBehaviour Chart ISBN 0945320566.
 Wheeler, D J & Chambers, D S (1992) Understanding Statistical Process Control ISBN 0945320132.
 Wheeler, Donald J. (1999). Understanding Variation: The Key to Managing Chaos  2nd Edition. SPC Press, Inc. ISBN 0945320531.
[edit] External links
 Note: Before adding your company's link, please read WP:Spam#External_link_spamming and WP:External_links#Links_normally_to_be_avoided.
